SE203:/S31/M151

Sample Set Information

ID	SE203
Title	Untargeted metabolome analysis of Tomato (Micro-Tom) using LC-MS /LC-MSを用いたトマト（Micro-Tom）のノンターゲットメタボローム解析
Description	Untargeted metabolome analyses of Tomato (Micro-Tom) using liquid chromatography-mass spectrometry (LC-MS). The information on the peaks detected in this study was available at the Plant Metabolome Repository website (http://metabolites.in/plants). 液体クロマトグラフィー-質量分析（LC）を用いたトマト（Micro-Tom）のノンターゲットメタボローム解析です。 検出されたピークは、植物メタボロームレポジトリ (http://metabolites.in/plants) から公開されています。
Authors	Sakurai N1,2, Suda K1, Akimoto N1, Hoshi K1, Osawa S1, Ikeda C1, Ozawa K1, Yamada M1, Muneto R1, Shibata D1 (1 Kazusa DNA Research Institute, 2 National Institute of Genetics), Contact: sakurai AT nig.ac.jp (replace AT with @) 櫻井望1,2、須田邦裕1、秋元奈弓1、星久美1、大澤祥子1、池田千晶1、小澤馨史1、山田学1、宗藤玲子1、柴田大輔1（1 かずさDNA研究所, 2 国立遺伝学研究所）
Reference
Comment

Sample Information

ID	S31
Title	Tomato, Micro-Tom, flower
Organism - Scientific Name	Solanum lycopersicum
Organism - ID	NCBI taxonomy: 4081
Compound - ID
Compound - Source
Preparation
Sample Preparation Details ID	SS1
Comment

Sample Preparation Details Information

ID	SS1
Title	Preparation of the samples
Description	The plants were grown on a cultivation shelf. The plant parts were harvested, immediately frozen in liquid nitrogen, and stored at -80C. The sample was homogenated using mortar and pestle under liquid nitrogen into a fine powder and stored at -80C until use.
Comment_of_details

Analytical Method Information

ID	M151
Title	ESI Negative (Method 5)
Method Details ID	MS11
Sample Amount	5 mg FW / 20 uL injection
Comment

Analytical Method Details Information

ID	MS11
Title	LC-FT-MS, ESI, Negative
Instrument	Agilent1100 HPLC (Agilent), LTQ-FT (Thermo Fisher Scientific)
Instrument Type	LC-FTICR-MS
Ionization	ESI
Ion Mode	Negative
Description	Metabolite extraction 300 mg of powdered sample was mixed with 900 uL of 100% methanol solution containing 25 uM of 7-hydroxy-5-methylflavone as internal standard (IS). The sample was homogenized using Mixer Mill MM 300 (QIAGEN) at 25 Hz for 2 min, twice. The homogenate was centrifuged under 17,400 x g for 5 min at 4 C. A supernatant was passed through a Polytetrafluoroethylene (PTFE) filter (pore size 0.2 um, Millipore), and the filtrate was applied to a C18 silica column (MonoSpin C18, GL Science) to remove highly-hydrophobic contaminants. The filtrate passed through the C18 column was used for LC-MS analyses. The same extraction procedure with 75% methanol was performed without a sample to prepare mock samples and used as negative controls. Liquid chromatography (LC)-mass spectrometry (MS) analysis Agilent 1100 system (Agilent) and Finnigan LTQ-FT (Thermo Fisher Scientific) were used. Aliquots (5 uL) of the methanol extract were applied to a TSK-gel ODS-100V column (4.6 x 250 mm, 5 um, TOSO) and separated by water containing 0.1%(v/v) formic acid (Solvent A) and acetonitrile containing 0.1%(v/v) formic acid (Solvent B). The gradient program was as follows: 3% B (0 min), 97% B (90 min), 97% B (100 min), 3% B (100.1 min), and 3% B (107 min). The flow rate was set at 0.25 mL/min for 0-100 min and 0.5 mL/min for 100.1-107 min. The conditions of mass spectrometry were as below: - Method 1: This method is used for measuring the accurate mass of the peaks and obtaining MS/MS spectra. [Full scan] resolution, 100,000 by FT; m/z range, 100-1500 [MS2 scan] data-dependent scan by IT for the most intense 5 ions in the full scan. [Dynamic exclusion setting for MS2 scan] repeat count, 3; repeat duration, 30 s; exclusion list size, 500; margin, 10 ppm; exclusion duration, 20 s. - Method 2: Same as Method 1 except below: [Dynamic exclusion setting for MS2 scan] exclusion duration, 30 s. - Method 3: Same as Method 1 except below: [Dynamic exclusion setting for MS2 scan] repeat count, 2; exclusion duration, 30 s. - Method 4: Same as Method 1 except below: [Dynamic exclusion setting for MS2 scan] off. - Method 5: This method is used for obtaining MS3 spectra. [Full scan] resolution, 12,500 by FT; m/z range, 100-1500. [MS2 scan] data-dependent scan by IT for the most intense 5 ions in the full scan. [Dynamic exclusion setting for MS2 scan] same as Method 1. [MS3 scan] data-dependent scan by IT for the most intense 2 ions in the MS2 scan - Method 6: This method is used for obtaining MS2 spectra in high-resolution: [Full scan] resolution, 12,500 by FT; m/z range, 100-1500. [MS2 scan] data-dependent scan by FT for the most intense 5 ions in the full scan. resolution, 12,500. [Dynamic exclusion setting for MS2 scan] repeat count, 1; repeat duration, 30 s; exclusion list size, 500; margin, 10 ppm; exclusion duration, 40 s. - Method 7: Same as Method 5 except below: [Dynamic exclusion setting for MS2 scan] same as Method 2 ESI: electrospray ionization, FT: Fourier transformation ion cyclotron resonance type mass spectrometry, IT: ion trap type mass spectrometry. The mass analyses with electrospray ionization (ESI) in positive or negative modes were performed. The combinations of Methods 1-7 and ionization polarity are different between the samples, but at least one method for accurate mass measurement (Method 1-4) was applied for each sample. The raw data were acquired using Xcalibur software (Thermo Fisher Scientific).
Comment_of_details	[column] TSK-gel ODS-100V (4.6 x 250 mm, 5 micrometer; TOSOH) [gradient] Solvent A: water containing 0.1% v/v formic acid; Solvent B: acetonitrile containing 0.1% v/v formic acid; Gradient: 3% B (0 min), 97% B (90 min), 97% B (100 min), 3% B (100.1 min), and 3% B (107 min) [total separation time] 107 min